Planning a smart home: KNX or radio?
Last updated: 16 November 2026
Try it right away
Free in the browser; try it without an account. To save, export and share, create a free account.In a new build, KNX is the robust choice: a green bus cable of its own connects buttons and sensors, the actuators sit in the distribution board, and the system runs without radio, cloud or batteries. It costs more and has to be planned during construction. Radio (Zigbee, Thread and Matter, Z-Wave, Homematic IP, EnOcean) needs no cable of its own, is cheaper and fits existing homes too, but depends on batteries, range and a hub. Many plan mixed: KNX or at least conduits in the shell, radio for later. All numbers here are guideline values.
KNX and radio compared
| Feature | KNX (bus, twisted pair) | Radio |
|---|---|---|
| cable | a bus cable of its own to every button and sensor | none, only 230 V for mains-powered devices |
| when to plan | before plastering | any time, also later |
| actuators | DIN-rail devices in the distribution board | in the box, in the device or as a smart plug |
| hub | not needed, every device works on its own | usually needed (gateway, border router) |
| batteries | none | in buttons and sensors, replaced every few years |
| standard | ISO/IEC 14543-3, EN 50090, across manufacturers | each system its own standards |
| programming | with the ETS software by a professional | usually by app |
| cost | higher | lower |
KNX: bus cable, line and actuators
- Bus cable: J-Y(St)Y 2×2×0.8 or YCYM 2×2×0.8 with a green sheath. It runs as a line, star or tree to every device, just not as a ring.
- Actuators in the board: switch, dimmer, blind and heating actuators are DIN-rail devices. From there the 230 V wires run in a star to lights, sockets and shutter motors. So plan room in the distribution board.
- Power supply and IP router: every line needs a power supply; an IP router connects KNX to the network and the app.
| Limit of a KNX line (TP1) | Value |
|---|---|
| devices per line | at most 64 |
| cable length per line | at most 1000 m |
| distance between two devices | at most 700 m |
| distance of a device to the power supply | at most 350 m |
Line and area couplers connect more devices. A family house often manages with one line, rarely two.
Radio: Zigbee, Thread and Matter, Z-Wave, Homematic IP, EnOcean
| System | Technology |
|---|---|
| Zigbee 3.0 | IEEE 802.15.4, 2.4 GHz, mesh through mains-powered router devices |
| Thread | IEEE 802.15.4, IPv6 mesh, border router needed |
| Matter | application layer over Thread, Wi-Fi or Ethernet (CSA) |
| Z-Wave | 868 MHz in the EU, mesh |
| Homematic IP | 868 MHz |
| EnOcean | 868 MHz, battery-free buttons |
Planning rule (guideline): a mains-powered device that passes signals on as a repeater about every 10 m or two solid walls. Battery devices do not pass signals on. Zigbee, Z-Wave and Homematic IP need a hub, Thread and Matter a border router. With radio too, a neutral conductor in every switch box is worth it in a new build, because flush-mounted actuators usually need one.
Roller shutters and blinds
- Motors run on 230 V, as a guideline a roller shutter motor with about 110 W.
- Conventionally an NYM-J 5×1.5 runs from the blind button to the motor (L up, L down, N, PE, spare).
- With KNX the wire runs in a star from the blind actuator in the board, one channel per motor.
- External venetian blinds and venetian blinds tilt their slats, roller shutters do not.
- A weather station works as wind and sun guard for all blinds of a facade.
Equipment values 1plus to 3plus (RAL-RG 678)
The German guideline RAL-RG 678 adds building system technology after DIN 18015-4 to the stars of electrical equipment:
| Equipment value | Meaning |
|---|---|
| 1plus | minimum equipment plus preparation for building systems (conduits, boxes) |
| 2plus | standard plus at least one function area with a building system |
| 3plus | comfort plus at least two function areas |
Function areas are, for example, lighting, shutters and shading, heating or security.
What to provide in a new build in any case
- Conduits from every switch box to the distribution board, so a bus cable or another cable fits in later.
- Deep switch boxes with a neutral conductor for flush-mounted actuators.
- Room in the distribution board for actuators, power supply and spare.
- A network socket at the distributor for a gateway or IP router.
- A wire to every shutter box, even if the motor comes later.
Planning a smart home in RoomPlanning
In RoomPlanning you choose the building system (KNX, radio or mixed), place buttons, sensors, actuators and hubs on the floor plan and note with Controls what switches what. From that comes the function list with actuator channels, and RoomPlanning shows whether your plan reaches 1plus, 2plus or 3plus. Hints report radio rooms without a repeater and systems without a hub. With Premium the KNX check counts actuator channels and modules, compares them with the distribution board and checks 64 devices, 1000 m and 350 m per line. More on Plan a smart home and in the help Smart home and function list.

Family house with smart home (KNX)
159.7 m² · 11 rooms
Frequently asked questions
Is KNX worth it in a family house?
If you build new and want many functions, such as lights, shutters and heating per room, KNX is reliable and can grow for a long time. For a few functions or a small budget, radio is enough. Conduits to every switch box keep both options open.
Can I mix KNX and radio?
Yes. Many houses have KNX for built-in functions and radio for retrofits. Gateways connect the two, and Matter lets devices of different makers work in one app.
How many devices fit in a KNX line?
At most 64 devices on 1000 m of bus cable, with at most 350 m from the power supply to the farthest device. For more, a second line with a line coupler is added.
Do I need a hub for radio?
For Zigbee, Z-Wave and Homematic IP yes, for Thread and Matter a border router, often built into a speaker or router. Without a hub only single devices paired directly with their button work.
Which cable do roller shutter motors need?
As a guideline NYM-J 5×1.5 from the button to the motor, with KNX from the blind actuator in the board. Plan it even if the motor comes later.
Sources
The values are guideline values from freely available sources; DIN 18015-4 and the KNX standards are paid. Read on 16 November 2026:
- KNX Topology – Chipkin
- Installationsumfang und Ausstattungswerte – Baunetz Wissen (German)
- Press release on RAL-RG 678, 20 March 2023 (PDF) – HEA (German)
- DIN 18015-4 – DIN Media
This guide is general information with guideline values and does not replace planning by a qualified electrician.
