Smart home and function list

Choose the building system (KNX, radio or mixed), place buttons, sensors and actuators, link them with “Controls”, the function list with actuator channels, the KNX check, radio hints and motorised roller shutters.

In RoomPlanning you plan a smart home on the same layer as the network: you place buttons, presence detectors, window contacts, room control units and actuators as symbols on the floor plan, note which device controls which and, with KNX, draw the bus cable. From that come the function list with actuator channels and the equipment value with “plus” after the German RAL-RG 678. Drawing, control relations and hints are free; the KNX check and the function list as a file come with Premium.

Open the template in the editor

Choose the building system

With nothing selected, the Smart home section is on the right, also with the Network & smart home tool. There you choose the building system:

  • None (conventional): switches and sockets without bus or radio.
  • Prepared (conduits): conduits and boxes for a later system; that is the equipment value 1plus.
  • KNX (bus): a green bus cable to every button and sensor, the actuators sit in the distribution board.
  • Radio: Zigbee, Thread and Matter, Z-Wave, Homematic IP or EnOcean, without a cable of their own.
  • Mixed (KNX and radio): for example KNX in the new build and radio for retrofits.

Below it you see which equipment value your plan reaches. 1plus means prepared, 2plus needs a building system and one function area, 3plus two. RoomPlanning reads the function areas lighting, shading, heating and security from the control relations: what a button or sensor controls under Controls. If an area is still missing, it says how many.

Place devices

With the Network & smart home tool, the devices for smart home, security and audio are there beside the network symbols, among them:

  • Controls: push buttons with 1, 2 and 4 rockers, blind button, room control unit with display, smart display;
  • Sensors: presence and motion detectors, window and door contact, temperature and humidity sensor, water leak detector, weather station;
  • Actuators in the board: switch, dimmer, blind and heating actuators as DIN-rail devices, KNX power supply and KNX IP router, plus flush-mounted actuator, smart plug and valve actuator;
  • Hubs: smart home hub (gateway) and Thread border router;
  • Security and audio: cameras, door intercom, sirens, smart lock, ceiling and wall speakers, CO and heat detectors.

When you select a device with Select, the Device section sets the radio or bus system, the supply (mains, battery, bus or PoE) and the power. Under Controls you pick the devices this button, sensor or actuator switches, such as the ceiling light or the roller shutter, and for a control its function, such as switch, dim, shading, heating or scene.

Function list

Open function list in the Smart home section shows each control per room with its function, the devices it controls and the actuator channel. With KNX, RoomPlanning numbers the channels: “SW1.3” is channel 3 of the first switch actuator, “DM” stands for dimming, “BL” for blinds and shutters, “HT” for heating. When a placed actuator controls a device, its name and channel are shown.

In the list you edit the control relations as under Controls: add or remove devices and change the function. A placed button that controls nothing yet joins the list with Add control. With Premium the function list is also available as CSV and as a sheet in the drawings (Bill of materials and lists).

KNX check (Premium)

With KNX or mixed, RoomPlanning checks your plan as a whole with Premium:

  • Actuator channels: how many channels are needed for switching, dimming, blinds and heating.
  • DIN-rail devices (suggestion): for example 8-fold switch actuator, 4-fold dimmer, 4-fold blind actuator, 8-fold heating actuator, power supply and IP router, each with its modules (TE).
  • Distribution board: the modules of the KNX devices and the protective devices are compared with the size of the board you placed. If it is too small, it says Distribution board too small.
  • Line: the check counts the devices (at most 64 per line), measures the bus cable (at most 1000 m) and the farthest way to the power supply (at most 350 m), along the bus wires you drew. With more devices it suggests a second line with a line coupler.

On Free the section shows a blurred preview with the crown and the way to Premium.

Draw the bus cable

With the Network & smart home tool, choose the cable type Bus (KNX, door intercom) on the right and the cable, for KNX the green J-Y(St)Y 2×2×0.8. Click from device to device; a double click or Enter ends the cable. Unlike a network, a KNX line may run as a line, star or tree, just not as a ring. The wires to lights and shutter motors, on the other hand, run as NYM in a star from the actuator in the board.

Hints (free)

Below the function list RoomPlanning reports what is often forgotten with radio and 230 V devices:

  • a room with battery devices of a radio system but no mains-powered device of the same system that passes signals on;
  • Zigbee, Z-Wave or Homematic IP without a hub, Thread or Matter without a border router;
  • 230 V devices such as shutter motors or flush-mounted actuators on no circuit.

Select marks the devices in the plan. A shutter motor on a circuit appears in its legend.

Roller shutters and blinds

Pick a window or a door to the outside: the opening's panel has a Sun shading section. Switch it on and choose:

  • Kind: roller shutter, external venetian blind (raffstore) and awning (vertical screen) hang outside, venetian and pleated blinds inside.
  • Drive: by hand (strap, crank) or motor (230 V).
  • Box: built in (lintel box), surface-mounted or none.

Select several windows or walls (also with Ctrl+A) to set the shading of all their windows and outer doors in one step. Inner doors, garage doors, pocket doors and passages take none.

  • On the plan the box is a narrow dashed rectangle on the outer side of the opening, a motor an M in a circle on the Network & smart home layer. The SVG, PDF and DXF exports show the same (DXF: box on OPENINGS, motor on NETWORK).
  • In the drawings facades and wall views show the box as a band over the window.
  • In 3D the 3D view panel sets under Sun shading whether the blinds are open, half or closed. Raffstores and venetian blinds tilt their slats, a surface box sits over the window. The AI photo and the walkthrough keep the shading open.
  • Control: a blind button or radio button drives the motor through Controls in the Device panel. A weather station works as wind and sun guard for all shadings of a facade: Control a facade adds every shaded window of that facade, on all storeys.
  • Electrics: a motor counts as a load (roller shutter motor 110 W, raffstore motor 90 W). The guideline cable is NYM-J 5×1.5 from the blind button to the motor (L up, L down, N, PE, spare). Once a device controls the motor, Suggest cable draws it. With KNX it runs in a star from the blind actuator, one channel per motor; the KNX check counts the blind channels.
  • Bill of materials: it counts the shading by kind, drive and box with the motors' power, in the exports too.

Good to know