Estimate Wi-Fi coverage

How well Wi-Fi reaches each room: a heatmap over the floor plan, the share of each room, frequency band and transmit power, "Suggest access points" and what the estimate assumes.

Before the ceilings are closed you want to know where the access points belong. RoomPlanning estimates from your floor plan how strong the Wi-Fi is in every room: it shows a heatmap over the plan, the share of each room with good signal and suggests access points on the ceiling. The estimate comes with Premium. Placing access points and drawing cables stays free.

Open the template in the editor

Show Wi-Fi coverage

In the left bar under Building services, choose the Network & smart home tool. On the right, open Wi-Fi coverage and switch on Show coverage. A grid in three steps then lies over the floor plan of the storey:

  • Good, from −67 dBm: enough for video calls and streaming.
  • Enough, down to −75 dBm: browsing and mail work, video may stutter.
  • Weak, below that.

The steps differ in colour and in lightness. The legend sits at the bottom of the plan with the note Estimate, not a measurement. Below the settings, the panel lists every room with its share of good signal, and the living area of the storey at the top. The heatmap is always for the storey you are working on. Access points on other storeys count too, weakened by the slab.

The estimate runs in the background and only again when something that matters changes: walls, doors and windows, rooms, storeys, the settings or an access point. Moving furniture changes nothing.

Frequency band and transmit power

Under Frequency band you choose 2.4 GHz, 5 GHz or 6 GHz, under Transmit power the access point's power in dBm. The limit that applies to the band in the EU is shown beside the field. A new plan uses 5 GHz and 23 dBm. When you change the band, RoomPlanning sets the usual power for it: 20 dBm at 2.4 GHz, 23 dBm at 5 and 6 GHz. The plan stores both values, and one step back undoes them.

What the estimate counts:

  • Access points on the ceiling, on the wall and outdoors, and mesh repeaters.
  • Walls by thickness: up to 10 cm thin, up to 20 cm medium, thicker ones thick, room separators not at all. If you have set a wall's construction, that counts: drywall and timber thin, masonry medium (thick above 20 cm), concrete thick.
  • Doors and windows lose half as much as their wall, open passages nothing.
Wall or slab2.4 GHz5 GHz6 GHz
thin3 dB5 dB6 dB
medium10 dB14 dB16 dB
thick15 dB22 dB25 dB
per slab20 dB30 dB33 dB

Manufacturers' planning guides have no tables of their own for 6 GHz yet. RoomPlanning takes 5 GHz there plus a good 10 %.

Suggest access points

With Suggest access points, RoomPlanning places access points on the ceiling in the middle of rooms and halls until 95 % of the storey's living area has good signal. It uses as few as it can, at most eight per storey, and counts the access points already in the plan. All new devices come in one step, and Undo takes them back together. If the coverage is already enough, RoomPlanning says so and places nothing.

Then move the access points where they fit the building and draw the data cable to the distributor. How to do that is in Plan a network.

Good to know

  • The estimate follows free-space loss, P = transmit power − (20·log10 f − 27.55) − 20·log10 d − walls − slabs, with the receiver 1 m above the floor. Closer than one metre it counts one metre.
  • The estimate knows nothing about furniture, underfloor heating, mirrors, metal or the neighbours. It does not replace a measurement on site.
  • In 3D the heatmap lies just above the floor of the storey while you show it in the plan. It does not appear in the walkthrough or in the AI photo.
  • The rule of thumb is one access point per storey and about 60 to 100 m², less area per device in solid buildings. More in Plan network and smart home.