Terrain and slopes

Step by step on the house on a slope: ground level, spot heights, the garden level, an excavation as a light court, the slope in 3D, in the elevation and in the site plan.

Every plan has a terrain. It decides which storeys lie above and which below ground, where the lawn starts in 3D and where light wells and excavations are needed. Unless you change it, the terrain is flat. This guide shows it on the template House on a slope: the plot falls about 3 m from the street to the garden, the ground floor lies at street level, and below it a garden level opens towards the garden. It takes about five minutes.

Open the template in the editor

1. Open the template: the slope in the floor plan

Open the template and switch to the Ground floor in the Levels panel on the right. On the left, at the edge of the plot, stand the spot heights that shape the slope: −0.15 m up at the street, −3.05 m down at the garden. At the corners of the house stand the level marks of the ground, "GL −0.15 m" at the front and "GL −3.05 m" at the back.

The ground floor of the house on a slope. On the left at the edge two spot heights with −0.15 m and −3.05 m, at the corners of the house the marks GL −0.15 m at the top and GL −3.05 m at the bottom.
  1. Spot heights at the plot edge
  2. Ground level at the house corners

±0 is the finished floor of the ground floor. Every height in the plan refers to it.

2. Set the ground level

With nothing selected, you find Terrain on the right below the levels. It holds the Ground level: where the terrain lies, usually 15 to 60 cm below ±0. New plans start at −0.15 m. Below it RoomPlanning counts how many spot heights shape the terrain, and Show terrain in 3D hides or shows it in 3D.

On the right the Terrain section: Ground level −15 cm, the note about ±0, below it 8 spot heights shape the terrain and the switch Show terrain in 3D, on.
  1. Ground level
  2. Spot heights in the plan
  3. Show terrain in 3D

Outside the spot heights the ground level applies. Storeys that lie wholly below it carry a small excavation sign with the hint Below the terrain in the list of levels (Basements and lower levels).

3. Set a spot height

If your plot rises or falls, set spot heights. Here a hollow in the garden is added:

  1. On the left under Outdoors, choose the Spot height tool, or press J.
  2. Click a place on the site, here in the middle of the garden.
  3. Enter its Height above zero on the right, here −3.40 m. Below it you see how far the point lies above or below ground level.
On the left the Spot height tool with the key J, in the garden a new spot height with −3.40 m. On the right under Spot height the Height above zero −3.4 m and below it −3.25 m against ground level.
  1. Spot height, key J
  2. New spot height
  3. Height above zero

Several points make a sloping surface: RoomPlanning joins them into triangles. Four points at the corners of the plot are enough for an even slope. Drag points with the mouse; Delete spot height or Delete removes them.

4. The garden level in the hill

Switch to the Garden level. On the hill side it lies below the terrain: RoomPlanning draws the earth hatch along the outside of those walls, and the utility room's window sits in a light well. On the valley side it lies open, with a terrace door to the garden.

The garden level: utility room, hallway, plant room, bedroom, bathroom and garden room. Along the north wall and the upper sides the earth hatch, on the left a light well, at the bottom the sliding door to the garden without hatch.
  1. Hill side in the ground
  2. Light well
  3. Valley side, door to the garden

On a slope a storey can lie above ground on one side and below ground on the other like this. Switch the hatch under Layers with Earth.

5. An excavation or light court

An excavation lowers the terrain in front of a lower level so that basement rooms get daylight or a way out. Such an excavation is also called a light court or sunken courtyard. Here the bedroom gets a light court in front of its west window:

  1. Stay on the garden level. On a storey above the terrain the tool points out that excavations belong in front of a lower level.
  2. On the left under Outdoors, choose the Excavation tool, or press U.
  3. On the right, choose the Shape (Rectangle or Polygon) and the Edge: Retaining wall, 25 cm thick to start with, or Slope with its gradient; 1 : 1.5 is common.
On the left the Excavation tool with the key U, on the right the Excavation panel with Rectangle or Polygon and Retaining wall or Slope, below it the hint how to drag the rectangle.
  1. Excavation, key U
  2. Shape
  3. Edge
  1. Draw the area in front of the room: drag a rectangle from corner to corner, or click the corners of a polygon.

Select the excavation. Its Floor starts level with the storey's floor; on the right you change the Floor, Edge, Wall thickness or slope. Below them you see how far it reaches below the terrain, here 1.47 m.

The new excavation in front of the bedroom is selected, labelled −2.95 m in the plan. On the right Floor 0 cm with the line Floor at −2.95 m, up to 1.47 m below the terrain, below it Retaining wall, Wall thickness 25 cm and the switch Railing where the drop is over 1 m, on.
  1. Excavation in front of the bedroom
  2. Floor and depth
  3. Retaining wall or slope
  4. Railing where the drop is over 1 m

With a retaining wall, Railing where the drop is over 1 m puts a railing along the top as soon as the drop is more than a metre. The switch starts on. If you turn it off, RoomPlanning points out drops of more than 1 m (a guide value of the German state building codes to check). Under Surface you choose the excavation's floor. Add steps in the excavation with the Stairs tool and To the terrain.

6. The slope in 3D

Switch to 3D at the top. The lawn follows the terrain: up at the street the parking stalls lie level with the ground floor, down below the garden level opens to the garden. Where storeys reach into the ground, the building pit is left open, and so are excavations, light wells, outside stairs and ramps. The furniture is hidden for the picture.

The house on a slope in 3D: front left the parking stalls at the street, the house with its gable roof, on the right the garden lower down, and at the garden level the new excavation with its railing.
  1. Street side, up
  2. Garden, 3 m lower
  3. Excavation with railing

Hide the terrain with Show terrain in 3D under Terrain or the Terrain switch under 3D view, for example to see a lower level from outside. The walkthrough starts on the ground floor and walks on the terrain, up and down ramps and outside stairs.

7. The slope in the elevation

Under Drawings, the West facade shows the slope from the side. The ground line falls from the street (left, GL −0.15 m) to the garden (right) and drops to its floor at the excavation. Whatever lies below ground is drawn dashed.

The west facade: gable roof, ground floor ±0.00 m and garden level −2.95 m. The ground line falls from GL −0.15 m on the left down to the right, drops at the excavation to the floor of the garden level and lies low on the right. Parts below ground are dashed.
  1. Ground line on the slope

In sections an earth hatch lies below the ground line and beside the basement walls. The level mark shows the ground level, such as "GL −0.15 m".

8. The site plan with spot heights

Under Drawings, New sheet starts a sheet. Under Add you find Site plan with spot heights among More: the terrain with every spot height, the marks at the house corners, excavations, ramps and the outline of the house. Set the Scale on the right.

A new A3 landscape sheet with the site plan with spot heights at 1:200: the hatched outline of the house, the excavation, the spot heights at the edges and the GL marks at the house corners. At the top the Add button, on the right the scale.
  1. Add
  2. Site plan with spot heights

More about sheets and export under Drawings and export.