Underground garage, ramp and garage door

Step by step on a villa: draw a ramp down to the lower level, check its slope, the ramp section, garage door, parking spaces and cars.

An underground garage needs three things: a lower level for the garage, a ramp down from the terrain and a garage door. Parking spaces and cars then show whether everything fits. This guide shows it on the Villa with underground garage template: you draw the ramp from the street to the door, check its slope and fit out the garage. It takes about ten minutes. The basics of lower levels are in Basements and lower levels.

Open the template in the editor

1. Go to the lower level

Open the template and click Lower level in the Levels panel on the right. The small excavation sign next to its height shows that it lies below the terrain. The garage is a room called "Underground garage"; the storey's Room height (clear) is 2.60 m. At least 2 m should stay clear below the ceiling, beams and ducts.

On the right the Levels panel with the lower level selected at −2.8 m and the Room height field. In the plan the ramp from above and the underground garage below it.
  1. Choose the lower level
  2. Room height of the storey
  3. The underground garage room

2. Choose the Ramp tool

The villa's ramp is already drawn. To draw it yourself, click it and press Delete. Then choose the Ramp tool on the left under Openings & access, or press Q. First set its Width (3 m to start with) and Sides on the right: Retaining walls, Curbs, Railing or Open.

The ramp ends on the floor of the storey you are on, so stay on the lower level.

On the left the Ramp tool is selected, on the right the Width and Sides fields. In the plan the ramp is deleted; above the garage the open ground runs up to the street.
  1. Ramp, or press Q
  2. Width
  3. Sides
  4. First click: up on the terrain
  5. Double-click: in front of the door

3. Draw the ramp

Click the start of the ramp up at the street, then point by point along its centre line down to the garage door. Set bends and curves as with walls. Double-click or Enter finishes the ramp, Backspace takes the last point back.

At the top the ramp starts at terrain level, here −0.15 m; at the bottom it ends on the floor of the lower level at −2.80 m. If it is steeper than 8 %, it gets transitions of up to 3 m at half the slope at the top and bottom. If it is too short, it gets at most 30 % steep and ends higher.

Select the ramp: on the right are its length and slope, here 22 m and 13.9 %, and below Height at the top (start), Height at the bottom (end), Transition at the top and Transition at the bottom. The plan shows the slope of each section and the levels at the top and bottom. Under Surface you choose its paving.

The new ramp is selected: in the plan 7 % at the top, 13.9 % in the middle and 7 % at the bottom. On the right 22 m long, 13.9 % slope, the heights −15 cm and −2.8 m and two transitions of 3 m.
  1. Length and slope
  2. Height at the top and bottom
  3. Transitions at half the slope
  4. Slope of each section

4. Mind the hints

RoomPlanning checks the ramp against the German model garage ordinance (Muster-Garagenverordnung) and shows hints in the Garage hint box at the very top of the selected ramp's panel. Try it: set Transition at the top to 0. The ramp then bends by almost 13 % at the top, and the hint about a slope change above 8 % without a transition appears. Set the transition back to 3 m afterwards.

Transition at the top is set to 0 cm. At the top of the panel the yellow Garage hint box: slope change above 8 % without a transition, with the note that it is a guide value of the model garage ordinance.
  1. Transition at the top set to 0
  2. Garage hint

The hints never block anything. RoomPlanning checks these guide values on a ramp:

HintGuide value
Ramp too steepat most 15 % gradient
Change of gradient without a transitiona transition at the top and bottom for changes of more than 8 %
Ramp too narrowat least 2.75 m
Headroom too lowat least 2 m headroom where the ramp runs under the house

The values come from the German model garage ordinance. They are binding mainly for medium and large garages with more than 100 m² of usable area. For a garage at a family house they are good guide values, so each hint says where it comes from and that you should check your local building code. More in the guide Underground garage and ramp at a family house.

5. Look at the ramp section

Under Drawings at the top, the list on the left has a Ramp section for every ramp. It shows the ramp lengthwise with the terrain, the slope of each section, the transitions and the levels at the top and bottom. It shows whether the ramp fits from the terrain down to the garage floor.

The drawings with Ramp section 1 selected: the ramp falls from the ground level −0.15 m at 7 %, 13.9 % and 7 % to −2.80 m, with the lengths of the sections below.
  1. Ramp section 1
  2. Slope of each section
  3. Level at the garage floor

6. The garage door

Back in the floor plan, click the door at the foot of the ramp. On the right, Style shows Sectional door. You can also choose a Roller door, an Up-and-over door or a Side-hinged garage door. The opening then grows to at least 2.50 × 2.125 m. Below, set its Width and Height. A width of 2.50 m is usual for one car, 5 m and more for two. The villa's door is 3 m wide.

Place a new garage door with the Door tool (O) in the garage wall. Choose the style on the right before placing it or later on the selected door. The door shows in the floor plan with its own symbol and in 3D as a garage door.

The garage door at the foot of the ramp is selected. On the right Style Sectional door, Width 3 m and Height 2.13 m.
  1. The garage door
  2. Style: Sectional door
  3. Width and height

7. The parking spaces

The garage has an area with three parking spaces. A click into the garage selects the room, not the area, so select the area under Layers with the arrow next to Site. On the right, set the Stall width, Stall length and Angle to the first edge: 90°, 60° or 45°. Below you see how many stalls fit and how wide the aisle in front should at least be.

Draw new parking spaces with the Outdoor area tool (G). Choose Parking under Kind on the right and drag a rectangle or click a polygon, in the garage or outside. RoomPlanning divides the area into single spaces with markings and numbers, 2.50 × 5.00 m at 90° to start with.

The parking area in the underground garage is selected. On the right Kind Parking, Stall width 2.5 m, Stall length 5 m, angle 90° and the line: 3 stalls fit on the area, aisle in front at least 5.5 m.
  1. Kind: Parking
  2. Size of a stall
  3. Angle to the first edge
  4. Stalls and aisle
  5. The parking area

8. Park the cars

Open the Furniture library (F) and choose the Vehicles group at the top: bicycle, bicycle stand, compact car, sedan, SUV and motorcycle. The wallbox is under Electrical & services, and everything is in the search too. Put a car on each space and check that the doors open and that you can walk around the car.

The furniture library with the Vehicles group: bicycle, bicycle stand, compact car and sedan.
  1. Furniture library, or press F
  2. Vehicles
  3. Click a car, then into the plan

9. The garage in 3D

In the 3D view the terrain above the ramp is open. Switch off the storeys above and the Terrain on the right to see the whole lower level, with the ramp running down between its retaining walls to the door. On a walkthrough you walk down the ramp into the garage.

The villa's lower level alone in 3D: the underground garage with three cars, beside it the plant room, wine cellar, home cinema, gym and sauna. In front the ramp with retaining walls and railings leads to the door.

Your own underground garage

For an underground garage in your own plan:

  1. In the Levels panel, use the plus to add a Basement below. RoomPlanning switches to the new storey.
  2. Draw the garage with the Room tool and name it "Garage". On the right, Use then shows Automatic (Garage), and the area schedule counts it as a garage, not as living area.
  3. Draw the ramp and place the door and the parking spaces as above.

Checks in the garage

In the garage itself RoomPlanning also checks, each in the Garage hint box:

  • on a room used as a garage: clear height below 2 m,
  • on a parking area: stalls narrower than 2.30 m, or 2.50 m next to a wall, or shorter than 5 m,
  • on a garage door: narrower than 2.30 m.

More on planning a garage is on the page Plan a garage or underground garage.