Plan a network

Step by step on the detached house: place and label network sockets, draw data cables to the media enclosure, also through riser points, check the equipment of each room and print the network plan. Plus “Suggest network”, SAT and fibre.

Beside the electrical plan, your floor plan has a layer of its own for network and smart home. On it you place network sockets, the distributor with patch panel and router, access points and satellite connections, draw the cables to them and check for each room whether the equipment is enough. If you like, RoomPlanning suggests the whole network. All of it is free. Smart home, smoke alarms and the bill of materials have articles of their own: Smart home and function list, Smoke alarms and Bill of materials and lists.

This guide shows it on the Detached house 140 m² without building services (the template in the gallery has them drawn in already): you place two network sockets in the study and connect each to the media enclosure in the utility room. It takes about ten minutes.

Open the template in the editor

1. Choose the Network & smart home tool

The Network & smart home tool is in the left bar under Building services, right below Electrical. It opens the symbols of the catalog category Network & communication: network sockets, media enclosures, patch panel, network cabinet, router, fibre modem (ONT), access points and satellite connections. Type a name at the top, for example "Network socket", and click the symbol.

On the left under Building services, Network & smart home is chosen. Beside it the Network & communication panel with the search for network socket and the matching symbols.
  1. Network & smart home
  2. Search devices
  3. Click the symbol

2. Place symbols

Click on the plan where the device goes. Hold Shift while you click and the symbol stays in hand, so you place several in a row; on walls the symbols turn by themselves. Put network sockets on the wall, best next to a power socket, and access points in the middle of the ceiling of the area they serve. In the example two network sockets go into the study; the media enclosure already hangs on the wall of the utility room.

All network symbols sit on the layer Network & smart home. Hide the layer and they disappear from the plan.

The study with two network sockets, one on the wall to the utility room, one on the outer wall. In the utility room the media enclosure.
  1. Two network sockets
  2. Media enclosure

3. Label devices

The Network & smart home section on the right holds the Equipment level (minimum, standard or comfort), the German state (smoke alarms) and Label all. This button labels every network socket and access point at once from storey, room and number, for example "GF-ST-01", so plan and patch panel match.

When you select a device with Select, the Device section on the right shows:

  • Label, which you can also change yourself;
  • Radio or bus system, such as KNX, Zigbee, Matter or Cable (LAN);
  • Supply and Power (W), such as PoE with 15 W for an access point;
  • Patch panel and Port, where the socket ends in the distributor; these fields appear once a patch panel is on the plan;
  • Controls: which devices this button or actuator switches, such as a light or a roller shutter.
The first network socket is selected and labelled GF-ST-01. On the right in the Device section the label, radio or bus system, supply, power and controls.
  1. Label
  2. System, supply, controls
  3. The network socket

4. Draw cables

With the Network & smart home tool you draw data, bus and coax cables. On the right choose the Cable type (network (LAN), bus, antenna (coax), fibre or signal), the Circuit, the Cable and the Route zone. New circuit starts a new line, for example "Network 1". Then click from symbol to symbol as for a circuit, adding a corner with a click in between. A double click or Enter ends the cable. Network, bus and antenna cables are drawn dashed.

Connect each network socket to the distributor on its own, because a home network is a star: in the example every socket gets its own line with New circuit. The Cables & circuits section keeps all circuits and cables in view.

Across storeys a cable runs through a riser point (slab penetration): place the symbol at the same spot on every storey, easiest in a shaft, the technical room or a corner of the hall, and draw each storey's cable up to it. Riser points stacked over each other (up to 30 cm apart) are joined through the slab. The bill of materials counts the run with the storey height, and the installation view in 3D shows the riser point as a grey tube through the storey.

Two dashed data cables run from the network sockets in the study to the media enclosure. On the right Cable type Network (LAN) and the button New circuit.
  1. Cable type
  2. New circuit
  3. One cable per socket

5. Check the equipment of each room

The Equipment per room section compares each room of the storey with the equipment levels of the German standards DIN 18015-2 and RAL-RG 678 and shows what is missing: sockets, lights, data and TV, each placed and required, and Complete or Incomplete. Give your rooms names such as living room, kitchen or hallway; the check tells the kind of room by them (Rooms and areas). The values are guideline values, and the installation belongs to a qualified electrician.

The opened Equipment per room section with bathroom, children's rooms, hallway, main bedroom, storeroom and study, each with sockets, lights, data and TV.
  1. Equipment per room

6. Print

Print electrical plan in the Cables & circuits section prints the storey on a sheet of its own, the network & smart home layer included: sockets, distributor, access points and cables are on the sheet, beside power sockets and circuits, with the legends: the electrical legend with the power circuits and the network & smart home legend with the network, antenna, fibre, bus and signal circuits (Planning circuits).

On the right under Cables and circuits the circuits Network 1 and Network 2 and the button Print electrical plan.
  1. Print electrical plan
The printed plan of the ground floor with the dashed data cables from the study to the utility room and the legend with Network 1 and Network 2.

This is what the sheet looks like.

Below it are two more print templates: Print network plan shows only network, antenna, fibre, bus and smart home without the power circuits, Print full installation plan everything of the building services on one sheet, pipes and conduits included. Both have a legend per system with each cable type, the number of devices (for the network the outlets and ports) and the length with the verticals down to the sockets and the reserve (guideline value without waste). Printing is free; on Free the print carries the watermark, and guests sign up first, as with the other exports.

Suggest network

With the Network & smart home tool, the right side has the section Suggest network. Choose This storey or Whole house, the equipment value and, if you like, Ceiling access points. Suggest network shows the suggestion half transparent on the plan first, with a list on the right:

  • Sockets: every room gets the double sockets its equipment value asks for, less those already there. In the living room the first sits beside the TV furniture (else on the longest wall without a window), the second at the sofa; in a study one per desk, in a child's room at the desk, in a bedroom beside the bed. Sockets sit 30 cm high, at least 15 cm from corners, doors and windows and never behind furniture. Where everything below is taken, the socket goes into the middle zone at 115 cm.
  • Access points: with Premium by the Wi-Fi coverage, else one per storey and started 80 m² in the middle of the rooms.
  • Distributor: an existing media distributor or network cabinet stays. Else a new one goes into a technical or utility room (basement first) or the central hall, with a patch panel (24 or 48 ports, 25 % spare).
  • Cables: every socket gets its own Cat.7 cable in a star to the distributor, along the walls through the doors, in the ceiling zone. Between storeys the cables run through a riser point at the same place on every storey; if there is none, RoomPlanning suggests it too.
  • Ports and labels: every new socket and access point gets a patch panel port and a label after your pattern. The bill of materials and the patch list count with them.

Apply turns the suggestion into a single step that Undo removes again; Discard leaves the plan as it is. When the plan changes, the preview lapses. The suggestion is free but needs an account.

Antenna, SAT and fibre

Below it is the section Antenna, SAT and fibre:

  • SAT system: Add missing antenna sockets places the antenna sockets the equipment value asks for. The SAT dish goes on the roof (the roof face looking most to the south) or on the south wall. The distribution is a multiswitch with one cable per socket, 5/4, 5/8, 5/12 or 5/16 by the number of subscribers, or a unicable system (EN 50494/50607, up to 32 subscribers on one cable). From there one coax cable per socket runs in a star, as for the network. With it comes the note on earthing and equipotential bonding of the antenna after DIN EN 60728-11 (guideline: 16 mm² Cu earthing conductor).
  • Fibre connection (FTTH): the chain from the building entry point in the house connection or technical room to the fibre socket, then to the ONT and the router in the media distributor. Without a house connection room in the plan, as in a flat, the entry point lies outside; RoomPlanning then places only the fibre socket, ONT and router.
  • § 145 TKG: if the plan has more than one kitchen, RoomPlanning counts several dwellings and notes that new buildings then need a passive, high-speed-ready in-building network infrastructure with an access point (§ 145 (4) TKG, Germany). Single-family houses are exempt (para. 6), but it is recommended. The network operator sets the fibres per dwelling (guideline 2 to 4).

Here too, Suggest shows the preview with a list first, and Apply makes it one step. The bill of materials counts the multiswitch by the number of SAT sockets. All values are guidelines; installation belongs to a qualified electrician.

Exports and sheets

  • DXF: network, bus, antenna (COAX), fibre (FIBER) and smart home are on CAD layers of their own beside ELECTRICAL. Labelled devices are blocks with the attributes LABEL (the label) and TYPE (the device). With Premium the storey's Wi-Fi estimate comes along as lines at −67 and −75 dBm on the layer WIFI.
  • PDF, SVG and PNG show the layers visible in the plan; show or hide the Network & smart home layer before you export.
  • Sheets: under Add, the Building services section offers a storey's legends per system and Wi-Fi map, and the lists. Building services sheet set creates an electrical plan and a network plan with legends for every storey, plus bill of materials and patch list (Bill of materials and lists).
  • Bill of materials and patch list: the Bill of materials section counts sockets, cable metres with rings, patch panel, switch and PoE for free. The patch list with port, label, room and cable length and all exports come with Premium (Bill of materials and lists).

Good to know